Difference between revisions of "RF Tutorial Lesson 3: Network Analysis of a Simple Transmission Line Circuit & the Smith Chart"
Kazem Sabet (Talk | contribs) |
Kazem Sabet (Talk | contribs) (→What You Will Learn) |
||
(6 intermediate revisions by the same user not shown) | |||
Line 5: | Line 5: | ||
*Network Analysis | *Network Analysis | ||
*Multiport Network | *Multiport Network | ||
− | *Scattering | + | *Scattering Parameters |
− | *Impedance | + | *Impedance Parameters |
*Smith Chart | *Smith Chart | ||
|All versions|{{download|http://www.emagtech.com/downloads/ProjectRepo/RFLesson3.zip RF Lesson 3}} }} | |All versions|{{download|http://www.emagtech.com/downloads/ProjectRepo/RFLesson3.zip RF Lesson 3}} }} | ||
Line 50: | Line 50: | ||
<tr> | <tr> | ||
<td> | <td> | ||
− | [[File:RFTUT3_1.png|thumb| | + | [[File:RFTUT3_1.png|thumb|left|550px|The quarter-wave impedance transformer circuit tuned for f<sub>0</sub> = 2GHz.]] |
</td> | </td> | ||
</tr> | </tr> | ||
Line 62: | Line 62: | ||
<tr> | <tr> | ||
<td> | <td> | ||
− | [[File:RFTUT3_2.png|thumb|230px|The "Connections" tab of Network Analysis Test Panel.]] | + | [[File:RFTUT3_2.png|thumb|left|230px|The "Connections" tab of Network Analysis Test Panel.]] |
</td> | </td> | ||
<td> | <td> | ||
− | [[File:RFTUT3_3.png|thumb|230px|The "Sweep" tab of Network Analysis Test Panel.]] | + | [[File:RFTUT3_3.png|thumb|left|230px|The "Sweep" tab of Network Analysis Test Panel.]] |
</td> | </td> | ||
<td> | <td> | ||
− | [[File:RFTUT3_4.png|thumb|230px|The "Output" tab of Network Analysis Test Panel.]] | + | [[File:RFTUT3_4.png|thumb|left|230px|The "Output" tab of Network Analysis Test Panel.]] |
</td> | </td> | ||
</tr> | </tr> | ||
Line 78: | Line 78: | ||
<tr> | <tr> | ||
<td> | <td> | ||
− | [[File:RFTUT3_5.png|thumb| | + | [[File:RFTUT3_5.png|thumb|left|720px|Cartesian graph of the magnitude and phase of the S11-parameter.]] |
</td> | </td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
− | + | Next, go back to the '''Output''' tab of the Network Analysis Test Panel and choose the '''Z''' radio button in the "Parameter Set" section. Make sure you remove the check mark from the "Decibels" check box. From the top "Graph Type" options, choose '''Cartesian (Real/Imag)''', because you are more interested in the frequency response of the real and imaginary parts of the Z11-parameter, which are indeed the input impedance of your circuit. | |
− | Next, go back to the '''Output''' tab of the Network Analysis Test Panel and choose the '''Z''' radio button in the "Parameter Set" section. Make sure you remove the check mark from the "Decibels" check box. From the top "Graph Type" options, choose '''Cartesian (Real/Imag)''', because you are more interested in the frequency response of the real and imaginary parts of the Z11-parameter, which are indeed the input impedance of your circuit | + | |
<table> | <table> | ||
<tr> | <tr> | ||
<td> | <td> | ||
− | [[File:RFTUT3_8.png|thumb| | + | [[File:RFTUT3_6.png|thumb|left|230px|The "Connections" tab of Network Analysis Test Panel.]] |
+ | </td> | ||
+ | </tr> | ||
+ | </table> | ||
+ | |||
+ | Run another network analysis and view the output graph as shown below. Note that at 2GHz, the real part of the impedance is 50Ω and its imaginary part vanishes as you would expect for perfect impedance match. | ||
+ | |||
+ | <table> | ||
+ | <tr> | ||
+ | <td> | ||
+ | [[File:RFTUT3_8.png|thumb|left|720px|Cartesian graph of the real and imaginary parts of the Z11-parameter.]] | ||
</td> | </td> | ||
</tr> | </tr> | ||
Line 130: | Line 139: | ||
<tr> | <tr> | ||
<td> | <td> | ||
− | [[File:RFTUT3 12.png|thumb| | + | [[File:RFTUT3 12.png|thumb|left|720px|The S11-parameter plotted on a Smith Chart. The tracking bar shows the points corresponding to 2GHz.]] |
</td> | </td> | ||
</tr> | </tr> | ||
Line 189: | Line 198: | ||
<tr> | <tr> | ||
<td> | <td> | ||
− | [[File:RFTUT3 13.png|thumb| | + | [[File:RFTUT3 13.png|thumb|left|480px|Smith chart showing the variation of the S11-parameter with frequency at a fixed line length of 37.5mm.]] |
</td> | </td> | ||
+ | </tr> | ||
+ | <tr> | ||
<td> | <td> | ||
− | [[File:RFTUT3 14.png|thumb| | + | [[File:RFTUT3 14.png|thumb|left|480px|Smith chart showing the variation of the S11-parameter with line length at a fixed frequency of 2GHz.]] |
</td> | </td> | ||
</tr> | </tr> | ||
Line 204: | Line 215: | ||
<tr> | <tr> | ||
<td> | <td> | ||
− | [[File:RFTUT3_15.png|thumb| | + | [[File:RFTUT3_15.png|thumb|left|550px|The quarter-wave impedance transformer circuit with an inductive load.]] |
</td> | </td> | ||
</tr> | </tr> | ||
Line 241: | Line 252: | ||
<tr> | <tr> | ||
<td> | <td> | ||
− | [[File:RFTUT3_16.png|thumb| | + | [[File:RFTUT3_16.png|thumb|left|720px|Computed s11 data for line segment length L = 75mm and Z<sub>L</sub> = 100 + j80 Ω over the frequency range 1-5GHz.]] |
</td> | </td> | ||
</tr> | </tr> |
Latest revision as of 23:47, 8 November 2016
Contents
What You Will Learn
In this tutorial you will run a network analysis test of the simple transmission line circuit you built in the previous tutorial lessons. You will examine the Z- and S-parameters of your circuit and study the Smith chart.
Building the RF Circuit
Once again you will use the simple transmission line circuit of RF Tutorial Lesson 1 with the AC voltage source and the quarter-wave impedance transformer configuration. The following is a list of parts needed for this part of the tutorial lesson:
Part Name | Part Type | Part Value |
---|---|---|
AC1 | AC Voltage Source | 1V |
XTL1 | Generic T-Line | Defaults: Z0 = 70.71, eeff = 1, len = 37.5 |
R1 | Resistor | 50 |
R2 | Resistor | 100 |
Place and connect the parts as shown in the figure below:
Running a Network Analysis of Your RF Circuit
As a first step, you will run a "Network Analysis" test of your RF circuit. Network analysis calculates the S/Z/Y parameters of your circuit based on the port(s) you define for your RF circuit. In this case, you will define a one-port network with an input port established at the input of the T-Line between Node 2 and ground. In the Toolbox, select the Test Panel and check the "Network Analysis" checkbox. Open the Test's Settings dialog. It has three tabs at the top: Connections, Sweep and Output. In the first tab, Connections, you define the port(s) of your circuit. In this case, Port 1 is defined between Node 2 and the ground. Accept the default value of 50Ω for the "Reference Impedance". In the second tab, Sweep, set the start and stop frequencies to 1GHz and 5GHz, respectively. Select a linear scale interval and set the step size to 10MHz. This will provide a smooth graph of the port characteristics. In the third tab of the dialog, Output, go to the "Parameter Set" section and choose the S radio button to compute the scattering parameters. Since your circuit is a one-port, you will have the S11-parameter only. From the top "Graph Type" options, choose Cartesian (Mag/Phase). Check the checkboxes labeled Decibels and Degrees for magnitude and phase, respectively.
Run a network analysis. An output graph like the one shown below is generated. This graph looks like a resonant circuit with a deep notch for |S11| at 2GHz. This is the frequency at which the input reflection coefficients becomes zero.
Next, go back to the Output tab of the Network Analysis Test Panel and choose the Z radio button in the "Parameter Set" section. Make sure you remove the check mark from the "Decibels" check box. From the top "Graph Type" options, choose Cartesian (Real/Imag), because you are more interested in the frequency response of the real and imaginary parts of the Z11-parameter, which are indeed the input impedance of your circuit.
Run another network analysis and view the output graph as shown below. Note that at 2GHz, the real part of the impedance is 50Ω and its imaginary part vanishes as you would expect for perfect impedance match.
Plotting the S-Parameter on Smith Chart
The Smith chart is a very useful graphical tool for RF engineers. RF.Spice A/D allows you to plot the S-parameters of your circuit on the Smith Chart. For this purpose, open the Network Analysis Test Panel of the Toolbox once again, and this time choose the S radio button in the "Parameter Set" section of the Output tab. For the "Graph Type", check the "Smith" checkbox. In order to better view the data points on the Smith chart, change the step size to 500MHz in the Sweep tab of the test panel. Run a network analysis of your RF circuit with the following parameters: