Changes

[[Image:neoscanfig_A_II_14.png|thumb|right|300px|<i><b>Figure A-II.14</b>: Warning massage for missing AD and DA addresses..</i>]] When the A/D and D/A convertor drivers are not detected by the system, NoeScan Optical Bench Manager program prompts a warning as shown in Figure AII-14. Or sometimes NoeScan Optical Bench Manager program does not respond.

1. <ol><li><p>Turn off the [[NeoScan]] system and turn it on again.</p></li><li><p>Reboot the control computer.</p></li><li><p>Go to Window Application (Program) or “Measurement Computing” folder and click on “Instacal” (Figure A-II.15).</p>

2<center>[[Image:neoscanfig_A_II_15. Reboot png|thumb|center|600px|<i><b>Figure A-II.15</b>: Start the control computerInstacal driver controller program.</i>]]</center></li><li><p>You may be prompted with a message box as shown in Figure A-II.16 saying that the previous board name has not been deleted. Press “OK” button.</p>

3<center>[[Image:neoscanfig_A_II_16. Go to Window Application (Program) or “Measurement Computing” folder and click on png|thumb|center|600px|<i><b>Figure A-II.16</b>: Configure the Instacal driver controller program.</i>]]</center></li><li><p>The “Instacal” driver interface will list A/D and D/A board names – e.g. USB-1608FS board and USB-3114 (Figure A-II.1517).</p>

4<center>[[Image:neoscanfig_A_II_17. You may be prompted with a message box as shown in png|thumb|center|400px|<i><b>Figure A-II.16 saying that the previous 17</b>: Instacal driver controller program list A/D and D/A board name has not been deletednames. Press “OK” button</i>]]</center></li><li><p>Select USB-3114 and double click on it.</p></li><li><p>In USB-3114 Board Configuration window use the dropdown list and set at the D/A Ranges to +/-10V (default is 0-10V)as shown in Figure A-II-18. </p>

5<center>[[Image:neoscanfig_A_II_18. The “Instacal” png|thumb|center|400px|<i><b>Figure A-II.18</b>: Instacal driver interface will controller program list A/D and D/A board names – e.g</i>]]</center></li><li><p>Close “Instacal” driver interface and open [[NeoScan]] Optical Bench Manager program. USB-1608FS board </p></li><li><p>If the “Instacal” driver interface does not list A/D and USB-3114 (D/A board names as indicated in Figure A-II-19.17).</p>

6<center>[[Image:neoscanfig_A_II_19. Select USBpng|thumb|center|400px|<i><b>Figure A-3114 II.19</b>: Instacal driver controller program cannot detect A/D and double click on itD/A converters.</i>]]</center>

7. In USB-3114 Board Configuration window use the dropdown list and set at the D/A Ranges to +/-10V (default is 0-10V)as shown in Figure A-II-18.<ol type="a"><li>8. Close “Instacal” driver interface and open [[NeoScan]] Optical Bench Manager program.<p> 9. If the “Instacal” driver interface does not list A/D and D/A board names as indicated in Figure A-II-19. a. Double click on program “MCCRegistryFix3.exe”. You can find it in C:\ProgramData folder.</p></li><li><p>b. Unplug the USB cable from the [[NeoScan]] Optical Mainframe.</p></li><li><p>c. Plug the USB cable from the [[NeoScan]] Optical Mainframe.</p></li><li><p>d. Run “Instacal” program again. </p></li><ol>