Changes

Set lock-in amplifier parameters:

</p>

<li>

Select the Lock-in Amplifiers for each channel using the Lock-in Amplifier Selector and set their corresponding parameters.

</p>

</p>

</li>

 

Other parameters that should be directly set on SR844 RF lock-in amplifier – since they are not controlled (see Figure 3.13 in section 3.2.2):

</li>

</ul>

<li>

To set translation stage speed settings:

From “Visa COM” serial port drop-down list select the COM port that the X Linear Translation Stage is connected to. A COM port is a specific serial connection on a computer, such as COM3.

Set the speeds of translation stage from “Translation Speed” box (Figure 4.5). The default value is 10 mm/s – indicating that translation stage can move 10 mm per second.

Press “Set Speed” button to save the new settings. The system will respond with confirmation message “Set Speed OK” in information panel.

The Scan Speed is ~ 0.3 mm/s.

When translation stages power up, they need to be homed in order to get an accurate reference position. The home sensor is at the motor end of the stage. Press “Home Position” button.

In order to displace translation stage to a defined position along X-axis, enter the appropriate X coordinate in the X Position Setting Entry Box and then press “Move along X” button as shown in Figure 4.6. Similarly, enter the appropriate Y coordinate in the Y Position Setting Entry Box and then press “Move along Y” button to move to the defined position (see Appendix A-I for more details).

Use “Set Origin” button to define the starting point of the scanning area (Figure. 4.6). See Appendix A-I for more details.

To go to the origin, press “Move to Origin” button.

==== Height Settings Page ====

Set the probe height – the distance between the probe and the DUT surface – using the knob (Figure 4.7). If you are interested in high resolution scanning, you may skip the other parameters, which will be discussed later in the chapter on Far Field Measurements.

==== Scan Settings Page ====

In order to scan the distribution of electric field on a DUT, three parameters are needed to be known:

The step size ∆X and ∆Y that represents the spacing between points along X-axis and Y-axis, respectively;

Probe height or the distance of the probe to the DUT surface.

To set scan parameters, press “Scan Settings” tab in [[NeoScan]] Mapping Utility program (Figure 4.9).

Switch ON mode enable the user to scan the three channels simultaneously using a single Lock-in Amplifier.

Select the channel(s) you want to scan by checking the check boxes (Figure 4.10).

Use the Data Label text boxes to choose a name of the files the data to be written. By default the program automatically reads the current working channel. “Information” editor enables a user to add a text on the data file header.

The Data Label should have a maximum of 25 characters. Do not use “Empty Space” or any of the following characters: ` ! @ " # $ % ^ & * ( ) + = \ | / { } [ ] , > < : ; ?. Note that it is allowed to use “dot” in project name.

Set the step size in each direction in entry boxes labeled “Step Size X” and “Step Size Y,” respectively. These values are in mm.

Select “What Axis to Scan First?” By default the program start scanning Y-axis first. In either case the scan data is written in a file in the same format, see Figure 4.11.

The program will also calculate the “Single Move Time” for each scan point (without delay) and displays the “Estimated Scan Time”.

The user can control the dwell time from “Dwell Control” key (Figure 4.12). The Dwell Time is the amount of time spent recording the signal for one data point for a channel before moving to the next point. By default, “Dwell Control” key is set to “Auto”. This introduces few msec dwell time during the scan. To change the dwell time, select the “Manual” option from “Dwell Control” button and enter the desired value in box labeled “Manual Move Time” in “Manual Move Setting” section (Figure 4.12). You can view the new “Estimated Scan Time” by pressing the “Update Scan Time” button.

It is assumed that the scan parameters are set and the scan measurement setup has been setup. In order to start the scan, press “Scan Control” tab in [[NeoScan]] Mapping Utility program (Figure 4.13).

Press “Start Scan” button to start the scan.

The program displays 2D Amplitude and 2D phase contour plots of the measured amplitude and phase during the scan, as shown in Figure 4.14. Graphs are rescaled continuously during the scan. This enables the users to monitor the status of the scan. For instance, any sudden change or any instrumental failure can appears as anomalous pattern in either 2D plots.

The “Pause Scan” and “Stop Scan” buttons control the scan process. During scanning, use “Pause Scan” to pause temporarily the scanning. Pressing the “Stop Scan” button during scanning, will stop the scanning process.

The “Plot Display?” key allows a user to display 2D Amplitude graph in dBm or μV unit. Similarly, “Current Signal” and “Current phase” in information panel present the lock-in amplifier current readings during the scan (Figure 4.15).

A user can check the “Elapsed Scan Time” and view the current X and Y position of the probe from the information panel (see Figure 4.16).

During each scan, both the magnitude and the phase of a particular electric field component at a plane are measured. When the scan is completed, data are written in .DAT files in your defined (created) project folder, say “patch_2.349GHz,” in the parent folder, i.e.

During a scan, data is collected and immediately displayed by [[NeoScan]] Mapping Utility program. However, data will be written into the files at the end of the scan.

By default [[NeoScan]] Visualization Utility program consider the “Project Folder”:

C:\Users\[[NeoScan|neoscan]]\Documents\[[NeoScan]]\Projects

as the parent folder in which all saved data are stored.

In order to view the plots of scan data:

Press “Open File 1” button as shown in Figure 5.1. This opens up the dialog window, where direct you to the project in parent folder where you want to open a data file, see Figure 5.2.

Choose the desired data file – e.g., E_X_Dir.DAT in project folder patch2.349GHz – and then press “OK” button in the dialog window.

“Information Panel” and “Project Description” will display all scan information regarding the selected project and scan (Figure 5.3).

Press “Near Field Maps” tab from [[NeoScan]] Visualization Utility program to view the plots.

[[NeoScan]] Near Field Maps page displays either 2D or 3D plots of the amplitude and phase distribution of the scanned field from saved files. It includes 2D Plot page and 3D Plot page.

 

When you enter “2D Plot” page, 2D contour plots for amplitude and phase distributions of the scanned field are plotted and the maximum and minimum of their values are displayed in the boxes next to the graphs (Figure 5.4).

By default, the program plots fields in V/m units. You can use the key labeled “Amplitude Unit?” to display them in dBV/m (Figures 5.4 and 5.5).

The “Phase Shift” knob adds an angular shift (in degree) to the phase distribution (Figure 5.6).

The Phase Threshold knob will sets any phase below a minimum field threshold (in V/m) to zero. Figure 5.7 compares the 2D Phase graph without a phase threshold (left) with the one with a phase threshold when the minimum field is set to 10 V/m (right).

Press “Save Graphs” button to save all plots. The plots associated with a project are saved in a folder called “Plots” within the same folder.

You can zoom in and out the graphs by clicking on the zoom button (Figure 5.4).

 

To view 3D plots, press the “3D Plots” tab in Near Field Maps page (Figure 5.9).

3D Amplitude graphs can be plotted either in dBV/m or V/m using the key labeled “Amplitude Unit?”

The “Phase Shift” knob adds an angular shift (in degree) to the phase distribution.

Users can choose the plot style using “Plot Style” dropdown window (Figure 5.10). It includes:

cwLine

cwPoint

cwLinePoint

cwHiddenLine

cwSurface

cwSurfaceLine

cwSurfaceNormal

cwContourLine

cwSurfaceContour

The default format is “cwSurface.”

To adjust the graph degree of transparency use “Transparency” knob or Transparency Entry Box as shown in Figure 5.11.